Bedoukian   RussellIPM   RussellIPM   Piezoelectric Micro-Sprayer


Home
Animal Taxa
Plant Taxa
Semiochemicals
Floral Compounds
Semiochemical Detail
Semiochemicals & Taxa
Synthesis
Control
Invasive spp.
References

Abstract

Guide

Alphascents
Pherobio
InsectScience
E-Econex
Counterpart-Semiochemicals
Print
Email to a Friend
Kindly Donate for The Pherobase

« Previous AbstractAlways Lost but Never Forgotten: Gas-Phase Wall Losses Are Important in All Teflon Environmental Chambers    Next Abstract"Evaluation of bioactive compounds, volatile compounds, drying process kinetics and selected physical properties of vacuum impregnation celery dried by different methods" »

ACS Omega


Title:Chemical Emissions from Cured and Uncured 3D-Printed Ventilator Patient Circuit Medical Parts
Author(s):Krechmer JE; Phillips B; Chaloux N; Shomberg R; Daube C; Manchanda G; Murray S; McCarthy A; Fonseca R; Thakkar J; Loose B; Herndon SC; Jayne JT; Worsnop DR; Canagaratna MR;
Address:"Aerodyne Research, Inc., 45 Manning Road, Billerica, Massachusetts 01821, United States. Department of Ocean Engineering, The University of Rhode Island, 215 South Ferry Road, Narragansett, Rhode Island 02882, United States. Formlabs, Inc., 35 Medford Street, Somerville, Massachusetts 02143, United States. Computer Science Department, Brown University, Providence, Rhode Island 02903, United States. Department of Medicine, Brown University and Alpert Medical School, Providence, Rhode Island 02903, United States"
Journal Title:ACS Omega
Year:2021
Volume:20211108
Issue:45
Page Number:30726 - 30733
DOI: 10.1021/acsomega.1c04695
ISSN/ISBN:2470-1343 (Electronic) 2470-1343 (Linking)
Abstract:"Medical shortages during the COVID-19 pandemic saw numerous efforts to 3D print personal protective equipment and treatment supplies. There is, however, little research on the potential biocompatibility of 3D-printed parts using typical polymeric resins as pertaining to volatile organic compounds (VOCs), which have specific relevance for respiratory circuit equipment. Here, we measured VOCs emitted from freshly printed stereolithography (SLA) replacement medical parts using proton transfer reaction mass spectrometry and infrared differential absorption spectroscopy, and particulates using a scanning mobility particle sizer. We observed emission factors for individual VOCs ranging from approximately 0.001 to approximately 10 ng cm(-3) min(-1). Emissions were heavily dependent on postprint curing and mildly dependent on the type of SLA resin. Curing reduced the emission of all observed chemicals, and no compounds exceeded the recommended dose of 360 mug/d. VOC emissions steadily decreased for all parts over time, with an average e-folding time scale (time to decrease to 1/e of the starting value) of 2.6 +/- 0.9 h"
Keywords:
Notes:"PubMed-not-MEDLINEKrechmer, Jordan E Phillips, Brennan Chaloux, Nicholas Shomberg, Russell Daube, Conner Manchanda, Gaurav Murray, Sam McCarthy, Alex Fonseca, Rodrigo Thakkar, Jinen Loose, Brice Herndon, Scott C Jayne, John T Worsnop, Douglas R Canagaratna, Manjula R eng 2021/11/23 ACS Omega. 2021 Nov 8; 6(45):30726-30733. doi: 10.1021/acsomega.1c04695. eCollection 2021 Nov 16"

 
Back to top
 
Citation: El-Sayed AM 2024. The Pherobase: Database of Pheromones and Semiochemicals. <http://www.pherobase.com>.
© 2003-2024 The Pherobase - Extensive Database of Pheromones and Semiochemicals. Ashraf M. El-Sayed.
Page created on 16-11-2024